Need help troubleshooting your Geekvape Aegis Max vape device?
If you own the Geekvape Aegis Max Starter kit this Aegis Max troubleshooting guide will assist you to fix many of your potential problems. Here are some of the most common issues with this vape kit and ways you can troubleshoot them.
Diminished or Absent Vapor Production
- Symptom: The device generates little to no vapor.
- Potential Remedies:
- Battery Level Verification: Make sure the device is sufficiently powered. Plug it into a power outlet using the supplied USB cable and charge until the battery indicator signals a full charge.
- Coil Connection Examination: Confirm that the coil is correctly fitted in the tank. Detach the tank, clean the coil contacts, and securely reinsert it.
- Coil Replacement: If the coil is aged or worn out, consider swapping it with a fresh one. Coils have a finite lifespan and may require replacement for optimal vapor production.
- Wattage Adjustment: Try different wattage settings to find the best range for your coil resistance. Some coils may require higher wattages to produce adequate vapor.
Burnt or Dry Hits
- Symptom: The vapor exudes a burnt or dry taste.
- Potential Remedies:
- Coil Priming: Prior to using a new coil, prime it by soaking the wicking material with e-liquid. Let the coil sit for a few minutes to ensure thorough saturation and avoid dry hits.
- Wattage Reduction: High wattage settings can overheat the coil, resulting in a burnt taste. Dial down the wattage to a level that aligns with your coil resistance and vaping preferences.
- E-Liquid Level Verification: Ensure the tank is filled adequately with e-liquid. Vaping with low e-liquid levels can lead to dry hits.
- Coil Replacement: If the coil is aged or burnt, consider swapping it with a fresh one to eradicate the burnt taste and enhance vapor quality.
Tank Leakage
- Symptom: E-liquid is seeping from the tank.
- Potential Remedies:
- O-Ring Inspection: Check the tank’s O-rings for any damage or misalignment. Swap any damaged O-rings to ensure a proper seal and prevent leaks.
- Tank Tightening: Make sure all tank components are firmly fastened. Over-tightening can damage the O-rings and cause leaks.
- Appropriate Filling: Refrain from overfilling the tank, which can cause leaks. Fill the tank just shy of the maximum fill line to avoid excessive pressure buildup.
- Coil Missing or Misaligned: Ensure that the coil is properly installed and securely screwed into place. Misaligned or missing coils can lead to leakage, especially when the device is laid sideways.
- Cracked Glass: Check for cracks in the glass tank. Even small fractures can cause leaks. Avoid exposing the device to freezing temperatures to prevent glass damage.
- Drawing Too Quickly: Avoid taking fast, hard draws from the device, as this can pull e-liquid into the airflow chambers and cause leaks. Opt for slow, steady draws instead.
- Prolonged Storage: Empty the tank if you’re not planning to use the device for more than 24 hours to prevent e-liquid saturation and leaks.
- Flying: Empty the tank before flying to prevent leaks due to changes in air pressure.
- Overheating: Avoid leaving the device in a hot car or direct sunlight, as overheating can cause the e-liquid to expand and leak through the o-rings or airflow holes.
- Freezing: Store the device in moderate temperature conditions to prevent plastic parts from becoming brittle and susceptible to leaking in freezing temperatures.
Device Fails to Power On
- Symptom: The device doesn’t turn on.
- Potential Remedies:
- Battery Connection Verification: Ensure the battery is correctly inserted and making contact with the device. Cleanse the battery contacts if necessary for a good connection.
- Battery Charging: If the battery is drained, plug the device into a power outlet using the supplied USB cable and charge until the battery indicator signals a full charge.
- Battery Replacement: If the battery is damaged or defective, consider swapping it with a fresh one.
Auto-Draw Feature Inactive
- Symptom: The auto-draw feature doesn’t activate.
- Potential Remedies:
- Airflow Verification: Make sure the airflow vents are clear and not blocked. Obstructed airflow can prevent the auto-draw feature from activating.
- Device Cleaning: Thoroughly clean the device to remove any dirt or debris that might be affecting the airflow sensors.
- Settings Adjustment: Check the device settings to ensure the auto-draw feature is enabled. Consult the user manual for instructions on how to adjust the settings.
Buy your Geekvape Aegis Max kit today from Canada Vapes! Sold in Canadian dollars, shipped from Canada same day at the lowest prices in Canada. We even supply a free 30ml bottle of e-liquid! Or you can review all of our Vape Kits.
Do you have any additional Aegis Max troubleshooting tips? If so, please contact us and we would be happy to help you and add your issue to our Geekvape Aegis Max Troubleshooting Guide!
Checkout our related posts: Geekvape Aegis Max Instruction Manual and our detailed Geekvape Aegis Max Review
